#Cabinet vision reviews full#
When you make the leap to automated equipment, you’re going to have your hands full already without having the added burden of learning a new design software.
#Cabinet vision reviews software#
If you opt for the cheaper route keep in mind that most likely when you do get that new router or P2P you’re going to have to learn a new design software as well as the software related to your new equipment, and if/when you do make this leap, the less new stuff thrown into the mix the better, as far as I’m concerned. You can take the cheaper route now, or you can go ahead and spend the bucks with the future in mind. If you do all kinds of goofy curved reception areas, then you may well need to spend 8 to 10 grand on a package that will do what you need it to do.Īnother thing to consider is where you might be in the future with this thing, i.e., do you envision adding CNC equipment? Perhaps not tomorrow but what about next year, or three years from now? If that’s something that could possibly be in the future, a 500-dollar package is probably not going to get you there. If you build boxes and the only difference between the boxes is the length, a 500-buck package may well be all you need. Any one of the packages will give you decent graphics, but you’re more interested in the nuts and bolts of the thing: will you get accurate info out of it how long does the design process take stuff like that.Įach of these packages has its strengths and weaknesses, that’s why I suggest you have details about what you do specifically. Too many times a prospective software buyer gets caught up in the glitzy graphics. Have them show you how the setup will go, how the program works, and of course how you get the cabinets from a napkin or post-it note to client renderings, assembly sheets, cutlists, etc. I would strongly suggest that you have details about what YOU build and have the person doing the demo perform tasks as they relate to YOUR business. Count on a steep curve unless you get a less expensive program that doesn't do much. The more a program does and/or the more you want it to do, the steeper the learning curve. It pretty much does everything you need, and it's easy to step up to more bells and whistles if you want. I've got Solid Manufacturing also, although I started with CV's "Solid Lite" program - kinda middle-of-the-road priced. I do some high-end custom homes in both frameless and traditional face frame, and I do commercial work which also presents some tricky situations, and have been able to run them all through this program. I have been able to create just about anything my customers have asked me to with this program. The only problem is that the Solid line of Cabinet Vision is somewhat pricy and has a rather steep learning curve, but the power you get for what you pay is well worth it. I am presently using CabinetVision "Solid Manufacturing," which I find to be the best. Still and all, I would rate this program above all those previously mentioned. It too is a great little program that is similar to Cabinet Solutions but with much more power and better graphics, however, the reports do seem to need a little help.
Next I went to Kitchen Builder by CabinetVision. As far as the reports were concerned, they seem to be complete and well thought out. In fact, I had two customers comment on it. Since it lacks the power to really customize each cabinet (they do not have a cabinet editor in the program), the graphics looked somewhat cheesy to me. Next I tried Quisine, which I found to be very limited. I was not able to show mouldings or wood textures on my drawings, nor was I able to create a radius cabinet. The only drawbacks I saw were in the perspective views.
I started by purchasing Cabinet Solutions, which I found to be a great little program for the small shop, considering the cost it was very easy to set up and just as easy to run, the reports were adequate and in order. I have tried a few and can offer my thoughts. Many of these products have changed considerably with introductions of newer operating systems I would like to keep the feedback limited to the newer versions. It would be great to get some feedback from the real world. I am sure some do certain things better than others. I have had reps demonstrate them and they all seem like good products. I have not been able to find any articles that review these products and give comparisons. Many of you have used one or more of these products and most likely have an opinion about them. The products I have been considering are Cabinet Solutions, Cabnetware, Cabinet Pro, CabinetVision and KCDw. I am in the process of reviewing the different cabinet design and production softwares available.
0 kommentar(er)
